You gather a nice, well-furnished house and at least imagine the small steam spot on the corners of the wall. The first reaction is to pull off the moisture. But calm down! Before leaving the room, everything is important to understand. This article was written in the same as “What do you think?” Consequences:

Types and causes of wall moisture

Types and causes of moisture in the wall


Observing and understanding where the moisture is coming from. Basically, moisture can settle on the wall in three different ways. check out:

Top down

If the moisture is on top of the wall, then the problem is probably from the top. This type of moisture is characterized by the ingress of water through the roof, in the case of houses or through the ceiling of dwellings, in which case the problem usually comes from the dwelling above.

Any opening, crack or tear in the tile may be sufficient to allow water to penetrate and damage the wall. Clogged slides also cause moisture problems inside the house. Watch if there are water stains next to the mold, or if the wall is wet. In this case it is worth checking the roof conditions and if you notice damaged roof tiles, replace them immediately and clean the gutters.

In homes, it is ideal to request union support and talk to the neighbor to diagnose the location of the leak and correct the problem.

From the soil

Moisture from the ground is a little more complicated to solve because it affects the structural part of the house. In such cases, the wall is usually in direct contact with the soil, which absorbs the natural moisture of the earth. Moldy patches of this kind of moisture are concentrated near the ground and are moist.

The solution to this type of moisture is to isolate and remove the bottom wall. However, if it is not possible to achieve the structure of the house, it is best to use a good waterproofing product between the floor and the wall.

internally

Indoor humidity is usually associated with insufficient ventilation of the environment. The excess steam, which is mainly produced in rooms such as kitchen and bathroom, is the main responsible for the humidity. In these cases, better ventilation of the environment is sufficient to solve the problem. Also check that the size of the windows is suitable for the room, it is often necessary to swap the miter for a larger one to ensure proper air circulation.

One way to check for moisture coming from the environment or from the wall is to place a piece of foil over the stain for a few days. When mold stains occur between the paper and the wall, the source of moisture is inside. However, if the stain remains on the visible side of the paper, moisture comes from the environment.

Walls may also suffer from leaks in pipes and pipes, especially if the wall in question is near rooms such as bathrooms, service areas or kitchens. In this case, there is no way. The break will be inevitable. It is the only way to solve the problem.

How to draw moisture from the wall step by step

How to draw moisture from the wall step by step

After analyzing and treating the cause of the moisture, it is now possible to remove the stain from the wall and fix the problem once and for all. But do not even think about painting the wall before removing the stain. Because she will surely return.

Before painting a wall with mildew, it is important to clean it with bleach and mild soap. The tip is to spray bleach on the wall, wait a few minutes – the stain tends to decrease and lighten with the product alone – and then pass a soft sponge with soap. After this process, the wall can already get color.

However, if you have noticed that the moisture comes from the floor, you must apply an impregnating agent before painting. To do this, sweep and scrape each coat of paint in the moisture affected area, spreading the spot a little to make sure the entire mushroom is removed. Then apply a waterproof product. After the dry season, it is already possible to paint the wall. Preferably, use anti-mold paint to further protect the wall.

An interesting tip to protect the wall from mold and mildew is to apply a layer of lime before final painting. Some painters also use a mix of lime and white glue to waterproof the entire wall.

1. Avoid moisture in the house

Avoid moisture in the home

Better to heal than to always prevent. Because mold stains on the wall are not only an aesthetic problem, but can also bring health complications, especially in people with allergies, seizures, sinusitis and other respiratory problems. How to avoid moisture indoors:

2. Open doors and windows

How to draw moisture from the wall: open doors and windows

Air circulation is the main remedy for moisture. Keep the doors and windows open so that the air in the rooms can be circulated and renewed. The same applies to furniture, especially wardrobes, let them open from time to time to ventilate.

In the winter months, when the air is cooler, let the house breathe at least in the morning, and in summer, use the sun and the warmer air to let the moisture out of the house.

3. Patrol the house

How to get moisture out of the wall: patrol the house

Take one day every six months on average to check sanitary facilities, roofing, walls and furniture. Check if parts need to be replaced or repaired. This care keeps moisture away from your home.

4. Pull the furniture off the wall

How to draw moisture from the wall: pull out furniture


Never leave the furniture near the wall. It is ideal to keep a minimum distance of five centimeters so that air can circulate between the furniture and the wall. Check from time to time if the wall is damp. If you notice any moisture, pull the furniture out even further.

5. Use materials that absorb moisture

How to remove moisture from the wall: use materials that absorb moisture

Spread through the damp rooms, such as bathroom and kitchen, materials that absorb moisture. The most frequently mentioned are charcoal and gypsum. They suck the condensation into the environment and prevent it from getting to the walls.

6. Change wall coating

How to remove moisture from the wall: remove the coating

But even if you’re so reliant on moisture insisting you stay home, try changing the wall paneling. The most suitable for moisture absorbing walls are ceramic, granite and marble. Some types of textures have in their formula substances that make the wall waterproof, you can also opt for them.

Now just enjoy your house with the walls clean and without that nasty smell of the mold. And remember the slightest sign of moisture, open all the windows.

 

LEAVE A REPLY

Please enter your comment!
Please enter your name here